Search
Now showing items 1-10 of 25
An Investigation of Use Biaxial Data in Sheet Metal Forming Simulations
(WILEY-V C H VERLAG GMBH, 2010)
The use of biaxial data in sheet metal forming simulation of a DP600 steel sheet is investigated. The biaxial strain data is experimentally determined and the stresses are calculated by the inverse finite element method. ...
EFFECTS OF VARIATIONS IN ALLOY CONTENT AND MACHINING PARAMETERS ON THE STRENGTH OF THE INTERMETALLIC BONDING BETWEEN A DIESEL PISTON AND A RING CARRIER
(INST ZA KOVINSKE MATERIALE I IN TEHNOLOGIE, 2010)
The intermetallic bonding between an aluminium alloy piston and a cast-iron ring carrier must be able to withstand prolonged exposure to the high-pressure and high-temperature environment of a diesel engine. Weak cohesion ...
EFFECT OF SHEET THICKNESS ON THE ANISOTROPY AND THICKNESS DISTRIBUTION FOR AA2024-T4
(INST ZA KOVINSKE MATERIALE I IN TEHNOLOGIE, 2013)
In this study, the effect of sheet thickness on the anisotropy and thickness distribution at room temperature (RT) was investigated for AA2024-T4 sheets. The anisotropy was determined using automated strain measurement ...
INVESTIGATION INTO REASONS FOR MINIMUM MAJOR STRAIN OFFSETTING OF FORMING LIMIT CURVE OBTAINED WITH NAKAJIMA TEST FOR AA 2024-T4
(GAZI UNIV, FAC ENGINEERING ARCHITECTURE, 2014)
In a typical forming limit curve (FLC), the minimum major strain where the minor value is equal to zero is located at y axes. In many forming processes, failure occurs at this region. Many studies in literature indicates ...
Finite Element Simulation of Diametral Strength Test of Hydroxyapatite
(AMER INST PHYSICS, 2010)
In this study, the diametral strength test of sintered hydroxyapatite was simulated by the finite element software, ABAQUS/Standard. Stress distributions on diametral test sample were determined. The effect of sintering ...
Analysis of Forming Limit Diagrams of DP600 Steel at Various Deformation Speeds
(WILEY-V C H VERLAG GMBH, 2010)
The forming limit diagrams (FLDs) of DP600 steel at various deformation speeds are experimentally investigated. Results show that forming limit diagram of the material at various deformation speeds is not significantly ...
EVALUATION OF TENSILE PROPERTIES OF HIGH STRENGTH STEELS AT WARM TEMPERATURES AND VARIOUS STRAIN RATES
(VERLAG STAHLEISEN MBH, 2008)
The use of advanced high strength steels in automotive industry has been increased recently. Dual-phase (DP) high-strength steel, which is an advanced high strength steel, has gained great attention due to its high strength ...
EFFECTS OF THE ARTIFICIAL-AGING TEMPERATURE AND TIME ON THE MECHANICAL PROPERTIES AND SPRINGBACK BEHAVIOR OF AA6061
(INST ZA KOVINSKE MATERIALE I IN TEHNOLOGIE, 2015)
In this study, the effects of the artificial-aging temperature and time on the mechanical properties and springback behavior of AA6061 are investigated. The results reveal that the yield strength, the tensile strength and ...
EFFECT OF PRE-STRAINING ON THE SPRINGBACK BEHAVIOR OF THE AA5754-0 ALLOY
(INST ZA KOVINSKE MATERIALE I IN TEHNOLOGIE, 2011)
This study presents the effect of pre-straining on the springback behavior of the AA5754-0 aluminum-magnesium (Al-Mg) alloy sheet under V bending by an experimental and finite-element simulation studies. Pre-straining ...
ARTIFICIAL-NEURAL-NETWORK PREDICTION OF HEXAGONAL LATTICE PARAMETERS FOR NON-STOICHIOMETRIC APATITES
(INST ZA KOVINSKE MATERIALE I IN TEHNOLOGIE, 2014)
In this study, hexagonal lattice parameters (a and c) and unit-cell volumes of non-stoichiometric apatites of M-10(TO4)(6)X-2 are predicted from their ionic radii with artificial neural networks. A multilayer-perceptron ...